- ELECTRONICS
- >
- MaxxECU
- >
- PLUGIN ECUs
- >
- Nissan
- >
- Nissan Silvia S15 1992 - 2002
Nissan Silvia S15 1992 - 2002
SKU:
1854
$1,304.00
$1,304.00
Unavailable
Nissan S14A / S15 (SR20)MaxxECU Plugin ECU for Nissan S14A/S15 with SR20 engine
Fast installationRemove and replace the stock ECU. Replace the stock lambda sensor by an included wideband sensor. Installation completed in less than three hours
Raplace stock air-flow-meterRemove and replace the stock air-flow meter and replace it by a MaxxECU built-in boost sensor for up to 43 psi/ 3bar
SR20MaxxECU Plugin ECU for Nissan S14A or S15 with SR20 engine, with 64-pin ECU connector
Fast installationRemove and replace the stock ECU. Replace the stock lambda sensor by an included wideband sensor. Installation completed in less than three hours
Raplace stock air-flow-meterRemove and replace the stock air-flow meter and replace it by a MaxxECU built-in boost sensor for up to 43 psi/ 3bar
SR20MaxxECU Plugin ECU for Nissan S14A or S15 with SR20 engine, with 64-pin ECU connector
Selected MaxxECU advantages
Selected vehicle features
Selected MaxxECU functions
MaxxECU STREET technical
MaxxECU RACE technical
MaxxECU functionality
MTune tuning features
MaxxECU functionality
- Built-in MAP-sensor (up to 43 psi / 3 bar of boost pressure)
- MDash/RealDash Android app connectivity
- Superfast USB communication
- High or low impedance injector support
- No changes in original electronics
- Direct access to up to 8 EGT-sensors
Selected vehicle features
- Uses stock harness, easy installation
- The air mass meter is removed
- Controls idle valve, AC, tachometer and other instruments
- Stock lambda sensor(s) is replaced with the included wideband sensor
Selected MaxxECU functions
- Boost control
- Launch control
- Shift-cut
- Lambda control
- Boost level switching
- All 3-12 cylinder engines (4-stroke)
- Up to 6 cylinders fully sequentially
- Up to 12 cylinders in wasted spark
- Intake air temperature sensor (IAT)
- Coolant temperature sensor (CLT)
- Throttle position sensor (TPS)
- Lambda (WBO) sensor. Uses a sensor directly connected to the ECU without any additional electronics. Supports Bosch LSU 4.2, 4.9
- 2 trigger inputs. VR or digital. Automatic trigger level detection. The signals are processed by a completely separated processor for maximum performance and immunity against interference
- 2 extra temperature sensors. Can be used as switches or to control additional functions
- 2 0-5V inputs. Can be used for additional sensors such as for measurement of fuel/oil pressure
- 2 digital inputs used for example for speed sensors (Hall) or switches
- Built-in 400kPa MAP-sensor for up to 3bar/43PSI of boost
- 6 injectors outputs. High impedance only
- 6 ignition outputs. 5V signal to drive ignition modules, CDI units or coils
- 4 outputs for extra features. Can be used to control virtually anything. Fuel pumps, idle control, boost solenoids, nitrous, shift lights, fans, warning lights, etc. GPO 1-3 (2A), GPO 8 (5A)
MaxxECU STREET technical
- CAN bus (additional wires required)
- USB communication for tuning with MTune
- 8MB memory for internal logging, up to 1000Hz
- Supply voltage 8-22V
- ARM Cortex-M3 120MHz main processor
- Resolution on ignition: 0.1 degrees
- Resolution on injectors: 0.001 ms
- Updates the fuel and ignition calculations 2000 times per second
- The fastest PC communication on the market
- Weight: 520g
- 140x134x42mm (including mounting points, excluding connector)
- Aluminium casing
- All 3-12 cylinder engines (4-stroke)
- Up to 8 cylinders fully sequentially
- Up to 12 cylinders in wasted spark
- Intake air temperature sensor (IAT)
- Coolant temperature sensor (CLT)
- Throttle position sensor (TPS)
- Lambda (WBO) sensor. Uses a sensor directly connected to the ECU without any additional electronics. Supports Bosch LSU 4.2 and 4.9
- 2 trigger inputs. VR or digital. Automatic trigger level detection. The signals are processed by a completely separated processor for maximum performance and immunity against interference
- 2 extra temperature sensors. Can be used as switches or control of additional functions
- 2 knock sensor inputs
- 6 extra 0-5V inputs. Can be used for additional sensors such as measurement oil/fuel pressure
- 4 extra digital inputs used for example speed sensors (VR / Hall) or switches
- 8 EGT TYPE-K/N inputs (1200C/2200F) in separate harness
- 8 peak/hold injector outputs. 1-2 high or low impedance injectors per output. 8A per output
- 8 ignition outputs. 5V signal to drive ignition modules, CDI units or coils
- 9 extra LOW DRIVING outputs for additional features. Can be adjusted to control virtually anything like fuel pumps, idle valves. GPO 1-8,10 (2A), GPO 9 (5A)
- 2 extra +12V DRIVING outputs (GPO 15,16) (2A)
- 4 extra motor outputs (ex E-Throttle). GPO 11-14 (2A)
MaxxECU RACE technical
- CAN bus for expansion modules, OEM vehicle CAN, ODBII
- USB communication for tuning with MTune Bluetooth for connecting to mobile devices with MDash
- 8MB memory for internal logging, up to 1000Hz.
- Supply voltage 8-22V
- ARM Cortex-M3 120MHz main processor. Three extra processors to handle the trigger, injectors and knock detection
- Resolution on ignition: 0.1 degrees
- Resolution on injectors: 0.001 ms
- Updates the fuel and ignition calculations 2000 times per second
- The fastest PC communication on the market
- 50Hz sampling rate on all EGT inputs
- 1000Hz sampling rate on all analog inputs
- Weight: 880g
- 155x195x40mm (including mounting points, excluding connector)
- 2D and 3D
- Shortcuts for most operations
- Interpolation
- Local autotune
- Live-logger
- Superfast USB connection
- Live tuning - No need to burn changes - instant save
- Distributor
- VR-sensor or digital (Hall, opto)
- Standard missing tooth (60-2, 36-1). Supports ranges from 2-1 to 180-4
- Multitooth trigger (2+1 to 180+1)
- Audi 5-cyl
- Nissan CAS
- Mitsubishi 4/2
- GM LSx
- Honda K20Z4 12+1 crank with 4+1 cam trigger
- Chrysler Hemi SRT-8 32-2-2
- Subaru EJ20
- Even teeth
- 2JZ 3-teeth 7 VTTi
- BMW 6+1 extra (VANOS)
- BMW 8-1 (VANOS)
- Volvo T5/T6 VVT
- Mitsubishi EVO (MIVEC)
- Ford Mustang 5.0 Coyote VVTi
- Porsche 996 2001-2005 M96/70 Variocam
- EGT fuel correction
- Lean power cut
- EGT power cut
- Rev limit
- Advanced warning and protection system
- Lambda fuel correction
- 4L80E/4L85E
- 4L60E/4L65E
MaxxECU functionality
- Launch control (up to three stages)
- Anti-lag using solenoid or E-Throttle
- Traction control
- Shift-cut
- Overrun fuel cut
- Lambda control (closed loop)
- Nitrous control
- AC control
- Boost control (closed/open loop), extra compensation tables.
- Boost level switching
- E-Throttle support
- VANOS/VVTi support
- Logging: Internal up to 1000Hz, PC logging 20Hz
- Built-in error diagnostics and handling
- Idle control using E-Throttle, idle solenoid, stepper motor or ignition timing
- Closed loop anti-stall
- Ignition timing lock for easy synchronization with timing light
- Flex fuel
- Speed limiters
- Individual fuel correction per cylinder
- Injector staging
- Virtual fuel tank/fuel consumption
- Filters on TPS, RPM and MAP signals
- Trailing ignition
- Virtual inputs/internal outputs to activate internal functions
- Use of TYPE-K sensor to report IAT up to 350 degree C/660 F
- Wastegate control with CO2 for predictable boost
- Extra user table activation based on user defined settings
- After launch power limit, function to control traction after launch
- CAN inputs (advanced) - Receive CAN data from external electronics
- and use in MaxxECU, such as OEM vehicle buttons.
- Automatic starting and stopping of internal log function based on
- user conditions (speed, load, error code etc.)
- Timers and distance counters
- CAN for OEM protocols, OBDII, and CAN modules
- Clutch slip control with user defined tables (as an example)
- Measure injector resistance directly from software
- Built-in trigger oscilloscope
- Built-in trigger logger
- Flexible load/speed axis selection
- Flexible user output functions
- Flexible user PWM/FREQ output functions
- Speedometer output function
- Tachometer output selectable 5/12V, supports external flyback coil
- Sequential gearbox control
MTune tuning features
- 2D and 3D
- Shortcuts for most operations
- Interpolation
- Local autotune
- Live-logger
- Superfast USB connection
- Live tuning - No need to burn changes - instant save
- Distributor
- VR-sensor or digital (Hall, opto)
- Standard missing tooth (60-2, 36-1). Supports ranges from 2-1 to 180-4
- Multitooth trigger (2+1 to 180+1)
- Audi 5-cyl
- Nissan CAS
- Mitsubishi 4/2
- GM LSx
- Honda K20Z4 12+1 crank with 4+1 cam trigger
- Chrysler Hemi SRT-8 32-2-2
- Subaru EJ20
- Even teeth
- 2JZ 3-teeth 7 VTTi
- BMW 6+1 extra (VANOS)
- BMW 8-1 (VANOS)
- Volvo T5/T6 VVT
- Mitsubishi EVO (MIVEC)
- Ford Mustang 5.0 Coyote VVTi
- Porsche 996 2001-2005 M96/70 Variocam
- EGT fuel correction
- Lean power cut
- EGT power cut
- Rev limit
- Advanced warning and protection system
- Lambda fuel correction
- 4L80E/4L85E
- 4L60E/4L65E
MaxxECU functionality
- Launch control (up to three stages)
- Anti-lag using solenoid or E-Throttle
- Traction control
- Shift-cut
- Overrun fuel cut
- Lambda control (closed loop)
- Nitrous control
- AC control
- Boost control (closed/open loop), extra compensation tables.
- Boost level switching
- E-Throttle support
- VANOS/VVTi support
- Logging: Internal up to 1000Hz, PC logging 20Hz
- Built-in error diagnostics and handling
- Idle control using E-Throttle, idle solenoid, stepper motor or ignition timing
- Closed loop anti-stall
- Ignition timing lock for easy synchronization with timing light
- Flex fuel
- Speed limiters
- Individual fuel correction per cylinder
- Injector staging
- Virtual fuel tank/fuel consumption
- Filters on TPS, RPM and MAP signals
- Trailing ignition
- Virtual inputs/internal outputs to activate internal functions
- Use of TYPE-K sensor to report IAT up to 350 degree C/660 F
- Wastegate control with CO2 for predictable boost
- Extra user table activation based on user defined settings
- After launch power limit, function to control traction after launch
- CAN inputs (advanced) - Receive CAN data from external electronics and use in MaxxECU, such as OEM vehicle buttons.
- Automatic starting and stopping of internal log function based on user conditions (speed, load, error code etc.)
- Timers and distance counters
- CAN for OEM protocols, OBDII, and CAN modules
- Clutch slip control with user defined tables (as an example)
- Measure injector resistance directly from software
- Built-in trigger oscilloscope
- Built-in trigger logger
- Flexible load/speed axis selection
- Flexible user output functions
- Flexible user PWM/FREQ output functions
- Speedometer output function
- Tachometer output selectable 5/12V, supports external flyback coil
- Sequential gearbox control